13 DIY Electronics Projects for Beginners (To try in 2024)

Hay! looking for some amazing and best DIY electronics projects for beginners to try out? Well, then you are in the right place. Because today I am going to share some cool beginners useful electronic projects that I am pretty sure you gonna like.

You are here it means you have some kind of attachment for electronics. I am sure you love electronics not as much as I may think but hay you love it and believe me loving electronics and getting to know more about it is like exploring how the world around us works.

You can clearly see we are living in the world of electronics, the number of electronic devices has surfaced the number of human beings. That is very true. So, I personally think it is very important to learn electronics to have a clear picture of our modern-day society.

Now, I talked too seriously above. But hay! my intention was to just give you a glimpse of what is going on and to motivate you that doing these amazing DIY electronics projects for beginners is your right step in the right direction.

I hope you will enjoy this article 😊

Let’s get started.

The Best DIY Electronics Projects For Beginners

You know, all DIY electronic circuit projects are great and fun. Deciding which DIY to try totally depends on what you personally like or prefer or just resonate with. Every DIY is providing the same values i.e.

• Improving your soldering skill
• Practicing soldering
• Learning electronics concepts
• Getting to know various electronics components and learning how they are working in the complete circuit
• Learning how to properly use various electronics components
• Learning about the right pin configuration, and a lot of other beneficial reasons.
• Learning about circuit schematic diagrams

But the point is, it doesn’t matter what DIY you choose, you will have the same learning experience. So please enjoy the following list and have fun.

Tips before we start

I know, you are excited about all the best DIY electronics projects for beginners but first, let just go through some useful soldering tips. We need to make sure to take the right actions at the right time so that we can ensure our security and increase the chances of proper working DIY at the end.

• The soldering iron can’t touch the components for a long time(1.0 seconds), otherwise, it can damage the components.
• Pay attention to the positive and negative of the components.
• Strictly prohibit short circuits.
• The user must install the LED according to the specified rules. Otherwise, some LEDs will not light.
• Install complex components first like the ICs.
• Make sure all components are in the right direction and right place.
• Check that all of the LEDs can be illuminated.
• It is strongly recommended to read the installation manual before starting the installation.
• Please wear anti-static gloves or anti-static wristbands when installing electronic components.

1. YM™ – YE13 DIY Power Supply

It is always good to start doing electronics projects that help you build types of equipment that you will use for a long time, that you will use every day for your projects.

One of such best DIY electronics projects for beginners is designing a power supply, you enjoy it building, you enjoy it soldering, and you also get a working power supply at the end as well. Just perfect!

The beauty of this amazing DIY electronics project is you have an outstanding end product. The end product is not only a power supply but you also get a pulse signal generator as well. So this is like two in one.

Important features of this one of the amazing DIY electronic projects for adults and students:

• Adjustable output voltage – best for use in many projects, can be used to power up various kinds of other devices
• Output voltage range: 1.25 – 12.5V
• Power: 1.5W This is a very high value and enough to power a lot of devices.
• Power supply + Signal generator
• Awesome buzzer option

In summary, YE13 DIY Power Supply (Product link) is a very good starting DIY. I personally like this DIY electronic project for beginners. If you also liked it, give it a try I promise you will have a lot of fun assembling and soldering this DIY project.

2. YE™ – YE10 DIY FM Radio

The other one of the simple electronic projects for school students would be this FM Radio. Enjoy the DIY and at the end get yourself a quality FM radio that can tune from 88 – 108MHz.

Important features:

Let’s talk about the key features of this amazing FM radio kit. The feature that makes it stand out is the glass case. After you solder the kit place each part (i.e the PCB board, load speaker, and antenna) in the provided transparent glass case to give the kit the look and taste of an amazing end product.

• Easy to solder (Through Holes Components)
• State of the art PCB boards and traces
• Long antenna for higher gain purposes
• Working voltage: DC 5V direct current (positive and negative inside the DC seat, do not reverse)
• Circuit board size: 7.7 x 6.1 (cm)
• Shell size: 8.4*7.6*5.5 (cm)
• Frequency modulation range: 88MHz-108MHz Enjoy all your favorite radio stations
• FM button, to help in selection and tuning to various FM stations
• Digital display
• Frequency function
• Power-off memory function: After turning off the power, power on again to play the radio station before the power-off.
• Power saving function

In summary, YE10 DIY FM Radio (Product link) is one of the amazing DIY electronics projects for beginners. I like it myself if you like it too give it a try. It is worth each and every penny.

3. YE™ – YE01 DIY Sounds Box

As the name for this electronics DIY  project suggests, this DIY has to do something with creating amazing sounds. You will enjoy the soldering and at the end, you will have a working device that with the setting of a binary code can actually create sounds.

Four different switches are used to create a four digits binary code. That code associates with a sound that this DIY will produce using a quality buzzer. This is amazing.

Important features of this best DIY project for beginners:

• Able to create 16 different sounds using a unique binary code
• Exposure to IC soldering: this would be great for new beginners
• IC sockets provided for safe soldering i.e. to lower the risk of burning the IC chip
• High-quality PCB board with thick traces
• Binary code practice with four different switches
• Think terminals components

In the summary, YE01 DIY Sounds Box (Product link) is one of the amazing DIY electronic projects for beginners for so many reasons. It is very unique and very interesting to see how electronics can be used in such a way that can produce sounds.

4. YE™ – YE04 DIY Adjustable Supply

Another interesting idea for an amazing DIY electronics project would be to make an adjustable power supply board. You can use it in your lab or to power up other devices. This DIY takes 24V AC input and can give a variable DC voltage from 0 – 30V. Is this not an interesting idea to work with?

Important features:

• Input voltage: 24VAC
• Input current: 3A maximum
• Output voltage: 0 to 30V continuous adjustable
• Output current: 2mA – 3A continuously adjustable
• Output voltage ripple: minimum 0.01%
• All straight inserted element
• LED indicator
• Circuit protection
• Overload and short circuit protection
• Minimum current (2mA) under the measurable LEDs and Zener diode

In summary, this YE04 Adjustable Supply (Product link) is an amazing DIY electronic project for beginners and for everyone who wants to learn or practice soldering.

5. YE™ – YE02 DIY Light Sensor

Another creative idea would be like doing something with light and sensors. You know there is a tool or you may say the sensor that can detect the light we see around us. The technical name for the sensor is Light Dependent Resistor (LDR). The LDR has the property its resistance changes when light falls upon it.

This amazing electronics DIY project has just used LDR this unique property of changing resistance upon falling of light. The DIY is silent and spying as a secret detective in dark. But once it detects light the buzzer goes on.

Important features of one of the simplest DIY electronics projects for beginners

• Simple circuit
• Easy to solder
• Exposure to LDR soldering
• Exploring how to use a variable resistance to control the sensitivity of a circuit.
• A good soldering practice for complete beginners

In summary, YE02 DIY Light Sensor (Product link) is an amazing DIY for those who are just started with soldering or electronics and want to see quick results. Like you know it is motivational to see little circuit works, it gives them the confidence to take further right steps.

6. YE™ – YE12 DIY Metal Detector

The next DIY is a noncontact metal detector. As the name suggests this DIY will detect any metal material you bring near to it. This is like a security project that you can solder to find out metal. Just like a security system at the airports.

Important features of this best DIY project for beginners:

• Can be a good security device for your home, office, or lab
• Can be a good learning kit for electronics beginners to know about circuit schematics, how components are connected together on a PCB board.
• Operating voltage: 3-5V (DC)
• Operating current: 40mA
• Standby current: 5mA
• Detection distance: 60mm
• Alarm mode: Both light and sound (A quality is there to make sounds upon the detection of metal)
• Best for (Level): Beginner level

In summary, YE12 DIY Metal Detector (Product link) can be another cool DIY electronic project for beginners that you can give a try if you want to challenge yourself to solder a little complex PCB board as a beginner.

7. YE™ – YE09 DIY Frequency Counter

For counting or measuring signal frequency you need a frequency meter. And this amazing DIY just does this. After you carefully solder all the components together. You will have an end device that can count signal frequencies up to 50MHz.

Important features:

• LED display to show the data clearly
• Can measure the oscillation frequency of most commonly used crystals
• Automatic range conversion without manual switching
• Programmable addition and subtraction frequency settings can measure radio transceivers.
• Includes five precision resolutions and power-saving mode.
• The display will be turned off automatically if there is no obvious change within 15s.
• With a transparent case, components can be well protected.
• Wide Power Supply, can be powered by USB/external power(5~12V)/9V battery.

In summary, YE09 DIY Frequency Counter (product link) can be one of the best DIY electronic projects for beginners. You will not enjoy soldering it but in the end, you will have a working frequency counter.

8. YE™ – YE11 DIY Lucky Turntable

As the name is telling the whole story. Almost every one of us has played this turntable game using an empty bottle. The idea behind this DIY is the same but a try is made to make the game much cooler by using modern electronics.

Important features of one of the amazing DIY electronics projects for beginners

• You see the DIY consists of 10pcs 5mm red light-emitting diodes.
• After pressing the switch, the LED lights flash rapidly in turn, and randomly stay after a few seconds.
• One of the LEDs is on and the other LEDs are off. This formed a lucky turntable.
• The PCB for this kit is of high quality to ensure a smooth soldering experience.
• You will have exposure to solder IC without using any IC sockets.

In summary, YE11 DIY Lucky Turntable (product link) is another interesting DIY electronics project for beginners that you can try on and have an amazing time with.

9. YE™ – YE05 DIY Christmas Tree

Another interesting idea to put your soldering skill to test is to try rotating flash LEDs Christmas tree. I know probably it would not be Christmas the moment you are reading this article but who knows?

It doesn’t matter if it is Christmas or not, by making this DIY I am pretty you will have an amazing time like Christmas. I am sorry if I am showing too much interest in this DIY. Probably I love LEDs too much.

Watch the video yourself and then decide. This would be the end product once you finished soldering it correctly.

Important features of this wonderful beginner’s DIY electronics project

• 37 pcs highlight LED
• Simple circuit, designed for easy and smooth soldering
• Mesmerizing music effect
• Automatic rotation
• RGB LED flashes automatically
• An adjustable cycle of the bottom LED
• Bottom LED breathing light effect
• Working voltage: DC 4.0V~5.5V
• Working current:500mA
• Power type: DC
• Color: RGB LED
• Working temperature:-40℃~85℃

In summary, YE05 DIY Christmas Tree (Product Link) is an RGB Music Christmas tree kit that consists of a circuit board and allows 37pcs LED flash with music and showing a Christmas tree in RGB (the night environment has better viewing).

It has a built-in motor so that the Christmas tree can rotate automatically which can achieve better dynamic effects when it is working.

10. YE™ – YE06 DIY Weevil Eye

This DIY is best suited for a complete beginner with no experience at all. It doesn’t mean other people can’t try it for fun.

The Weevil Eye is designed to look like a little beetle whose eyes glow in accordance with the ambient light level – the less light detected, the brighter the friendly weevil’s eyes will glow.

There is no programming involved and all soldering is beginner-friendly, so this kit is perfect for the embedded electronics novice.

Important features:

• High-quality PCB
• Exposure to LDR (light depended resistor)
• Exposure to transistor soldering for beginners

In summary, the YE06 DIY Weevil Eye (Product Link) is the best starter DIY at least you should try. It is an introductory electronics kit designed to help novice electronics enthusiasts learn about things like soldering and resistance.

11. YE™ – YE08 DIY AM/FM Radio

In the above we talked about the FM but what if some of you really want to try both FM and AM. If this is the case then we have gotten you another DIY that you try to have exposure to both FM and as well AM spectrum.

Important features:

• FM band uses CD9088 chip which is a dedicated monolithic FM radio chip
• Simple external circuit, designed for easy soldering
• Built-in frequency of 70kHz phase-locked loop system
• The mute circuit can suppress non-IF signal and too weak IF signal
• Including automatic frequency control system can be used for mechanical tuning,
• Power polarity protection
• Rod antenna for receiving the electromagnetic energy i.e. radio signals
• AM7642 integrated circuit TA7642 has 10 internal transistor compositions, the appearance of the package is used in the form of TO-92
• The audio output signal is coupled to the input of the power amplifier integrated circuit TDA2822 for power amplification to drive the speaker.
• Amplitude band using straight-type integrated circuit TA7642, receiving frequency range 525-1605KHz, with a simple circuit, the assembly success rate is high, there is a better selectivity; power amplifier circuit with TDA2822, with a large sound quality sound advantage
• This kit uses a 3V (DC) power supply

In summary,  YE08 DIY AM/FM Radio (Product Link) is one of the best DIY electronics projects for beginners where you get exposure to solder a little complex circuit.

Also, you get exposure to Radio Frequencies concepts. You get to know how RF waves travel and how a simple circuit with an antenna can catch them and convert them to audible sounds that we can hear and understand.

12. YE™ – YE07 DIY Audio Level Indicator

Imagine you have a circuit with a bunch of LEDs. These LEDs automatically turn ON depending on the sound in the environment.

For example, in a quiet place, every LED is OFF but in a room where there is loud music, all the LEDs are glowing with the rhythm of the music. Isn’t this would be an amazing DIY to try on?

Important features:

• DC input power supply: 9-12V
• Parameters are printed directly on the PCB board for convenience (You can make this DIY without looking at the manual)
• HAL treated pad
• State of the art PCB quality
• Designed for soldering practice
• Easy to solder (You can complete it in less than an hour time)

In summary, YE07 DIY Audio Level Indicator (Product Link) has a bunch of LEDs attached to a special IC.

Now when you place this circuit in a noisy environment the LED bar will glow according to the sound intensity. The louder the sound of music or anything the brighter the LED will glow. Don’t you think it is so far one of the amazing DIY electronic projects for beginners?

13. YE™ – YE03 DIY Piano kit

As you can see that fun is right there in the title, the Piano. Yes, you are right after soldering this DIY you will have a small piano ready to play with. Of course, this is not a professional or high-quality piano because our intention here is to learn electronics and soldering.

Important features:

• Power supply: DC3-12V
• PCB size: Length 13.5CM* width 2.2CM.
• Simple to solder PCB board
• Exposure to IC soldering i.e. NE555 timer
• Extra IC is provided to ensure you don’t damage the IC chip (This is added for beginners people)

In summary, the YE03 DIY Piano kit (Product Link) is a simple DIY piano kit that will bring a beautiful smile to your face. It takes a few hours to solder depending on your set skill, and at the end, you will a simple small piano that can play some mesmerizing sounds.

It is simple and practical, and the power consumption is small, and the circuit is driven by an integrated circuit i.e. 555 timer IC.

Summary of some of the best DIY electronics projects for beginners

In summary, I would say, this article is all about presenting a list of some unique and interesting DIY electronic projects for beginners. An effort is made to enlist some very fun DIYs so that a beginner can enjoy soldering them.

All DIYs presented in the article are using state of the art PCBs to ensure smooth soldering. The purpose of each DIY is to:

• Improving your soldering skill
• Practicing soldering
• Learning electronics concepts
• Getting to know various electronics components and learning how they are working in the complete circuit
• Learning how to properly use various electronics components
• Learning about the right pin configuration, and a lot of other beneficial reasons.
• Learning about circuit schematic diagrams

At the last, I would say be careful when you solder because a little mistake can harm you and can permanently damage the DIY as well. Don’t worry about making mistakes like heating a component too much or burning resistors and ICs. These are the ways you will learn. But try to be smart and make sure of everything before you take action

Thank you and have a good life.